Boot lace up tutorial (Archive this thread) [Archive] - OSW: One Sixth Warrior Forum

View Full Version : Boot lace up tutorial (Archive this thread)



Brett
05-16-2004, 19:28
I worked on this all day, I really hope it helps.

Here is the tutorial I promised, on how I add laces to molded boots. Let me start by saying that in no way are these instructions written in stone, they are the result of receiving some assistance from folks here at OSW and from trial and error on my part. I first got the idea to attempt adding laces to my molded boots and shoes, after seeing some done by ScanManDan. My first attempt at this ended horribly, as all I could find was 1/8 eyelets, and they were huge. DevilGuns and MindXStorm then steered me in the right direction by telling and showing me what materials worked best for this application. If you have a better way of doing any of the steps, please feel free to add them. First a list of the items I use:

Exacto knife
Fine pointed and duller pointed tweezers
Scissors
Eyelet setting tool (purchased from http://www.goodietwoshoes.com/index.cfm?fuseaction=detail&id=8688&product=13 )
Sharp pointed metal thing, it is some kind of metal punch with a fine point (sorry, but I donít know exactly what this thing is, I bought it at Joannís though)
1/16 eyelets purchased at AC Moore craft store in a multi pack which had several colors in it
Imitation leather cotton cording .5mm in size (purchased from http://www.firemountaingems.com/shopping.asp?skw=KWCORDCOTT )
Dremel with a small drill bit
Super Glue
Small piece of flat leather, purchased at Joannís
Boots

http://68.84.94.8/tutorial1.jpg

You begin by cutting out the tongue area of the boot with the exacto. Make sure you do not cut past the edge of where the molded eyelets are. You can actually cut more inside the tongue area, and go back and clean it up, but if you cut into the edge of where the molded eyelets are, you will not leave yourself enough rubber/plastic for the eyelets, and it will tear through.

http://68.84.94.8/tutorial2.jpg

What it should look like when you are done.

http://68.84.94.8/tutorial3.jpg

Trim the molded laces off of the eyelet area of the boot. You can actually trim all of the molded eyelets off, as well. I do this on some boots, and donít on others. Some boots have molded eyelets that are not straight, and if you use them as a guide, your new eyelets will go all over the place and will not look as good.

http://68.84.94.8/tutorial4.jpg

Once you have the tongue area cut away, it is time to make the holes for the eyelets. I use the eyelet setting tool, as mentioned above, but you may use whatever you are comfortable with, and have available. I know MindXStorm uses a leather punch to accomplish this.

http://68.84.94.8/tutorial5.jpg

As so:

http://68.84.94.8/tutorial6.jpg

Once you have all of the holes punched out, it is time to set the eyelets. Begin by using a toothpick, and placing one of the eyelets on the end, like so:

http://68.84.94.8/tutorial7.jpg

Place a small drop of Super Glue in the hole. I have found a super glue gel to work best, as it will not drip into the boot.

http://68.84.94.8/tutorial8.jpg

Place the eyelet into the hole with the toothpick, making sure the eyelets is as flush as you can get it, as such:

http://68.84.94.8/tutorial9.jpg

Once all of the eyelets have been set in the holes, and the glue has been allowed to dry, use the dremel (with a small drill bit on it) and clean out each of the eyelets. This is a very important step, as the dried glue tends to clog the eyelets up, as well as the rubber from the boot (as the rubber on a lot of boots is thicker than the eyelets are long). The cleaner the hole is the easier they will be to get the laces into.

http://68.84.94.8/tutorial10.jpg

Once the holes have been cleaned out, it is time to get the laces ready. I cut approx 6Ē more lace material than I actually need to do the job, for a couple of reasons. First of, with this particular cord material (imitation leather, cotton cording) the ends will start to fray, making it all but impossible to thread the cord through the eyelets, and you will need to cut a small amount away to get the the un-frayed portion. Secondly, it is easier to tuck in any extra cording, into the boot, when they are tied, than it is to cut it to the needed length, and need to untie and re-tie them later. For the Corcoran boots, I cut approx 2.5 feet, per boot, and for most boots and shoes I cut approx 2 feet per boot.

http://68.84.94.8/tutorial11.jpg

Begin feeding the cording through the eyelets, pulling it all the way through from the inside, once you have it started. I have tried needles, and have not been able to find a needle that is large enough to fit the cording through on the end, and then have it fit through the eyelets. Therefore I feed the cording through using the fine point tweezers.

http://68.84.94.8/tutorial12.jpg

Once the laces have been threaded all the way up, it is time to make the tongue. I found some thin leather pieces at Joannís, and cut the tongues from this. I cut the tongues in approx 1/2 ď strips, and round off one end:

http://68.84.94.8/tutorial13.jpg

http://68.84.94.8/tutorial14.jpg

The completed product:

http://68.84.94.8/tutorial15.jpg

The completed Corcoran boots on my two new Soldat 2 figures:

http://68.84.94.8/tutorial16.jpg

http://68.84.94.8/tutorial17.jpg


I really hope this helps. Please let me know if you have any questions, or if I forgot to add anything. Thanks a lot!!!

ransomechua
05-16-2004, 19:37
Thanks for the lesson Brett!

Ran

Alyasha
05-16-2004, 19:42
Brett...YOU ROCK !
One of the most helpful and concise tutorials I have evere seen .
The boots look awesome .
Thanks !
:thumb

Devilguns
05-16-2004, 19:44
Very cool tutorial Brett:thumb I'm glad you posted the full figure shots of your Soldats, they look incredible!

I use the same Loctite products, excellent super glue:)

Hollowpoint
05-16-2004, 19:47
Wow! What a fantstic "how to". This should be archived as the template for how to write "how to's". Those are some wonderful boots there.

deadsel
05-16-2004, 20:19
WOW!!! thanks alot for showing us all how to do this!!!

Blowstuffup4fun
05-16-2004, 20:25
Great tutorial man!My only question is what did you do with the tounge?

billpete
05-16-2004, 20:37
man what a sweet tutorial...great job!!!

pukingdog
05-16-2004, 20:45
And all w/o bloodshed! Peer pressure triumphs! (Ya manipulative basrad, you were gonna do this along along...I feel *sniff* so cheap and used, LOL)

Archive material w/o a doubt, nice job, Brett!

Ockie
05-16-2004, 21:03
Great tutorial. Excellent work, can't wait to get the items and try this.

John.

steel bonnet
05-16-2004, 21:06
WOW very clear & precise.

May give that a go myself :D
Thank`s again & as said to your first pair you did yesterday..OUTSTANDING work on those boots :D

Ja
Steel Bonnet

Von Cougar
05-16-2004, 22:08
brett you came through 100%
a great tutorial to an amazing procedure. thanks a lot to those who helped brett with this project, you've all done the rest of us a great favour.
i honestly can't wait to get started on my own. all i need to do is, er, buy all the stuff. crap.

thanks again, brett, a perfect how-to